Ericsson RX8000 Series Especificações Página 1

Date of issue: 8th April 2013 WNE v.5.1 RLS & WNE CLIENT V.5.1 RX8200 CONFIGURATION GUIDE

Receiver Configuration RX8200 Configuration Guide 10 3.5 CONFIGURATION OF NETWORK ACCESS Access to the RX8200 should be configured on a client si

Receiver Configuration RX8200 Configuration Guide 11 Figure 11 RX8200 Default Status – Not Configured Alarm messages will be displayed on this St

Receiver Configuration RX8200 Configuration Guide 12 3.7 AUTOMATED CONFIGURATION SCRIPT A selection of automated xml scripts exist for an RX8200

Receiver Configuration RX8200 Configuration Guide 13 Figure 14 File Upload Tab Example: If the site under consideration was the Reuters Bureau i

Receiver Configuration RX8200 Configuration Guide 14 3.8 DEFAULT SERVICE PRESET Now that the receiver has been correctly configured to the RLS Se

Receiver Configuration RX8200 Configuration Guide 15 3.9 RECORDING THE MAC ADDRESS As with the old EMR satellite receiver, an RX receiver also ne

Receiver Configuration RX8200 Configuration Guide 16 3.10 RECORDING THE UNIQUE HARDWARE ID The Unique Hardware ID is required by ICA in London to

Receiver Configuration RX8200 Configuration Guide 17 3.11 SAVING A CONFIGURATION FILE The RX receiver automatically saves each configuration sett

Receiver Configuration RX8200 Configuration Guide 18 3.12 RESTORING A CONFIGURATION FILE  From the Save/Load configuration tab on the RX8200 in

Receiver Configuration RX8200 Configuration Guide 19 3.13 RESET TO FACTORY DEFAULTS To clear current configuration settings, either overwrite an

Legal Information RX8200 Configuration Guide 2 © Thomson Reuters 2013. All Rights Reserved. Thomson Reuters, by publishing this document, does not

Troubleshooting RX8200 Configuration Guide 20 4 TROUBLESHOOTING 4.1 UNABLE TO LOCK TO THE WNE SIGNAL Items to verify:  Confirm that the Input s

FAQs RX8200 Configuration Guide 21 5 FAQS 5.1 DOES THE RX8200 RECEIVER WORK WITH THE OLDER WNE PCS? This receiver performs the same function as t

FAQs RX8200 Configuration Guide 22 Figure 30 ASI Input 5.4 CAN I CONNECT TO THE ADDITIONAL MANAGEMENT CONTROL PORT? The use Control Port 2 is sp

FAQs RX8200 Configuration Guide 23 Figure 32 A Light Single Ku Band LNB C Band C-Band & Ku-Band Digi-Ready LNBs – California Amplifier - http

Appendix RX8200 Configuration Guide i APPENDIX 1 1.1 MAC ADDRESS CHANGE – REPLACING AN EMR RECEIVER WITH AN RX8200. The onsite client scenario wi

Appendix RX8200 Configuration Guide ii 1.2 ICA CONTACTS This group in London are available to authorise and administer changes for WNE and RLS on

Appendix RX8200 Configuration Guide iii APPENDIX 2 CHECKING EXISTING EMR MAC ADDRESS 1. An EMR browser page can be accessed through any browser wi

Appendix RX8200 Configuration Guide iv APPENDIX 3 MANUAL CONFIGURATION OF THE RX8200 TO LOCK TO RLS AND WNE. The screen shot examples below show a

Appendix RX8200 Configuration Guide v Figure 39 Satellite Input Screen 3. Configure the satellite input parameters for the client site. Use the

Appendix RX8200 Configuration Guide vi 5. For WNE, two multicast IP addresses exist to distinguish between PAL/625 and NTSC/525 on Reuters WNE i.e

Table of Contents RX8200 Configuration Guide 3 TABLE OF CONTENTS 1 Introduction 5 1.1 Front Panel Controls 5 1.2 Front Panel LEDs 5 2 Rece

Appendix RX8200 Configuration Guide vii 7. To change the IP Output 2 address, select the Output tab. As this network interface directly connects

Appendix RX8200 Configuration Guide viii APPENDIX 4 RX8200 TECHNICAL SPECIFICATIONS. 4.1 PHYSICAL & POWER  Dimensions: (W x D x H) 442.5 x 5

Appendix RX8200 Configuration Guide ix  Connector: 2 x RJ 45  Format: 100/1000BaseT  Max. input rate: 208Mbps 4.7 IP HIGH SPEED DATA  MPE

Appendix RX8200 Configuration Guide x 4.8 GLOSSARY OF ABBREVIATIONS Abbreviation/Term Description C-Band C Band is the original frequency allocati

Appendix RX8200 Configuration Guide xi APPENDIX 5 RX8200 ALARM The Alarms page provides access to the alarm settings for the receiver. To view thi

Appendix RX8200 Configuration Guide xii Figure 44 RX8200 Alarm Menu Compatibility Vs Dynamic Mode Alarms The current dynamic mode alarm functional

Appendix RX8200 Configuration Guide xiii  Decoder 1/2/3/4/5/6 – Choose the alarm condition from the drop-down menu to be activated when decoder 1

Appendix RX8200 Configuration Guide xiv © 2013 Thomson Reuters. All rights reserved. Republication or redistribution of Thomson Reuters content,

Table of Contents RX8200 Configuration Guide 4 Appendix 2 Checking Existing EMR MAC Address iii Appendix 3 Manual Configuration of the RX8200 to l

Introduction RX8200 Configuration Guide 5 1 INTRODUCTION The RX8200 Receiver is a component of the MPEG-4 AVC/ MPEG-2/DVB compliant range of

Receiver Installation and Cable Connections RX8200 Configuration Guide 6 2 RECEIVER INSTALLATION AND CABLE CONNECTIONS Mount the RX8200 on a 19-in

Receiver Installation and Cable Connections RX8200 Configuration Guide 7 2.3 IP DATA AND MANAGEMENT CONNECTION Connect the Ethernet 3 (eth3) netw

Receiver Configuration RX8200 Configuration Guide 8 3 RECEIVER CONFIGURATION 3.1 SATELLITE PARAMETERS Global satellite coverage for the WNE and R

Receiver Configuration RX8200 Configuration Guide 9 Configuring the RX8200 The most efficient way to configure an RX8200 is by using its web-based