Ericsson 1553-FGC 101 1010 Uen A Guia do Utilizador Página 31
- Página / 196
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Installing the Equipment
Connecting the Unit to an AC Power Supply
Warnings!
Do not overload wall outlets and extension cords as this can result in a risk of fire or
electric shock.
As no mains switch is fitted to this unit, ensure the local AC power supply is
switched OFF before connecting the supply cord.
The unit is not fitted with an ON/OFF switch. Ensure that the socket outlet is
installed near the equipment so that it is easily accessible. Failure to isolate the
equipment properly may cause a safety hazard.
The EQ8096 can be fitted with dual power supplies each with a separate mains
connector. The equipment load is automatically split between the two power
supplies (if option fitted). If one power supply fails, the full load will be transferred to
the remaining serviceable unit allowing the faulty unit to be replaced without
switching off the equipment. To connect the unit to the local AC power supply:
2.4.3.1
1. Ensure the local AC supply is switched OFF.
2. Ensure the correct fuse type and rating has been fitted to both the equipment
and the AC power cables.
3. Connect the AC power leads to the EQ8096 mains input connector and then to
the local mains supply.
2.5 -48 V DC Power Supply
2.5.1 DC Power Supply
Note: Only models EQ8096/BAS/48V, EQ8096/BAS/SFP/48V and
EQ8096/HWO/DPS/48V use a DC power supply.
Cautions!
This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your business,
consult a qualified electrical engineer.
This equipment is Class 1 and must have a protective earth.
This product uses a –48 V DC power supply source (see Annex B, Technical
Specification) for a full power supply specification.
2/1553-FGC 101 1019 Uen A
2-9
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Manuais e produtos relacionados com Recetor Ericsson 1553-FGC 101 1010 Uen A
Recetor Ericsson RX8000 Series Especificações
(37 páginas)
(37 páginas)
Recetor Ericsson RX8000 Series Especificações
(26 páginas)
(26 páginas)
Recetor Ericsson RX8330 Especificações
(39 páginas)
(39 páginas)
Recetor Ericsson TT1222 Guia do Utilizador
(198 páginas)
(198 páginas)
Recetor Ericsson RX8200 Manual do Utilizador
(8 páginas)
(8 páginas)
Recetor Ericsson LBI-38505A Manual do Utilizador
(197 páginas)
(197 páginas)
Recetor Ericsson TT1222 Guia do Utilizador
(20 páginas)
(20 páginas)
Recetor Ericsson RX8315 Guia do Utilizador
(40 páginas)
(40 páginas)
Recetor Ericsson RX8200 Guia do Utilizador
(44 páginas)
(44 páginas)
Recetor Ericsson RX8315 Guia do Utilizador
(24 páginas)
(24 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais