Ericsson TT1222 Guia do Utilizador Página 44
- Página / 198
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Options
3.2.5 Setting Up the QPSK Input
Setting up the QPSK input is done entirely from the SETUP ⇒ INPUTS menu.
Table 3.5 steps through all the necessary settings to achieve signal lock.
Table 3.5: Tuning the Satellite Receiver
Step Action Result
1.
Go to the input menu, located
under the setup menu.
The display will read “SET: INPUT” on the
top line.
2.
Repeat pressing the up arrow, until
you are on the top line
The display will read “LNB Freq.:” on the
bottom line.
3.
Press right once, and then by using
the arrow keys as explained in
Chapter 4, enter the desired LNB
frequency.
The LNB frequency should be set to match
your external LNB.
4.
Go down one line, and edit the
satellite channel frequency
1
.
This sets up the tuning frequency in the
receiver.
5.
Go down to the next line, and enter
the Symbol rate.
This sets up the incoming symbol rate of
the demodulator.
6.
Continue on-line down to the Inner
Code rate, select the correct inner
code.
This sets up the Forward error correction
(FEC) rate of the demodulator.
7.
For the final three items, select the
correct LNB voltage, and turn 22
kHz control signal and spectrum
inversion on or off.
This finalises the set-up of the satellite
demodulator. Next to the menu name
(SET:INPUT), status information about the
signal lock is being displayed. (Signal
strength.)
3.3 Hardware Enabled Output Options
3.3.1 ASI Output (TT1222/HWO/ASI/OUT)
3.3.1.1 General
The ASI Output option provides a single ASI output on a BNC connector.
3.3.1.2 Connector Details
75 Ω BNC connector.
1
The satellite frequency should be within the area of the LNB frequency (±950 to 2150 MHz). If your frequency is outside this range, replace
your LNB with a higher or lower ranging unit.
EN/LZT 790 0002/2 R1A
3-6
- REFERENCE GUIDE 1
- Revision History 5
- Associated Documents 5
- Trademarks 6
- Warnings, Cautions and Notes 6
- EMC Compliance 7
- Contact Information 7
- Preliminary Pages 9
- Preliminary Pages 10
- 1 Introduction 11
- Introduction 12
- Warning! 13
- Caution! 13
- 1.2 Summary of Features 14
- Introduction 15
- 1.2.2 Inputs 16
- 1.2.3 Outputs 16
- 1.3 TT1222 Control Modes 18
- 1.4 Guided Tour 20
- 1.4.3 Rear Panel 22
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Read this First! 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 28
- 2.6 Signal Connections 32
- 2.6.2 Input Connectors 33
- 2.6.3 Output Connectors 33
- Installing the Equipment 35
- 2.6.4 RS232 Remote 37
- 2.6.5 Ethernet 38
- 3 Options 39
- Options 40
- 3.1 Available Options 41
- 3.2.1 Limitations 42
- 3.3.2 Dual ASI/SDI Output 45
- (TT1222/HWO/ASI/SDI) 45
- Options 47
- Chapter 4 49
- 4.1 Powering the Equipment 51
- 4.2.3 Editing a Menu Value 52
- 4.5 Service Configuration 53
- 4.6.1 Director 55
- 4.6.3 DVB Common Interface 56
- Chapter 5 57
- 5.1 Remote Control 59
- Step Action Result 62
- 6 Alarms/GPOs 63
- Alarms/GPOs 64
- 6.1 Introduction 65
- 6.2 Status LED 65
- 6.4 Alarm Relay 66
- 6.4.2 Configuring Alarms 67
- Table 6.5 69
- Chapter 7 71
- 7.1 Routine Checks 73
- 7.2 Servicing 73
- 7.2.2 Replacement Parts 74
- 7.3.1 Introduction 74
- 7.3.2 Warranty 74
- 7.3.4 Extended Warranty 75
- 7.5 Fault-finding 76
- A Glossary 77
- Glossary 78
- Glossary 79
- B Technical Specification 97
- B.1 General 99
- B.2 Key Features 99
- B.3 Video Decoder 99
- B.4 Outputs 100
- Parameter Performance 101
- B.4.4 PAN/SCAN 102
- B.4.5 VBI 625 Lines Output 102
- B.4.6 VBI 525 Lines Output 103
- B.4.7 Audio Decoder 103
- B.4.8 Analogue Audio Output 103
- B.4.9 S/PDIF Audio Output 104
- B.5 Data Communication 105
- B.5.3 Ethernet Port 106
- B.7 Options 107
- Parameter Specification 108
- Table B.17: ASI Input 108
- Technical Specification 109
- EN/LZT 790 0002/2 R1A 109
- Technical Specification 110
- EN/LZT 790 0002/2 R1A 110
- B.8 Power Supply 111
- B.9 Physical Details 112
- B.11 Compliance 113
- B.11.3 CE Marking 114
- B.11.4 C-Tick Mark 114
- B.11.5 Packaging Statement 114
- B.11.6 Packaging Markings 114
- B.11.8 Equipment Disposal 116
- B.11.9 Recycling 117
- C Front Panel LCD Menus 119
- Front Panel LCD Menus 120
- Front Panel LCD Menus 121
- C.1 LCD Menus 125
- C.2 Menu Tree 126
- EN/LZT 790 0002/2 127
- Menu Pages - Main Menu 128
- Presets Menu 128
- C.5 Setup Menu 129
- C.5.2 TV Service Menu 130
- Menu title: SET:TV 131
- SERVICE 131
- Description Section 131
- C.5.3 TV Service ID 132
- C.5.4 Audio 2 Service Menu 132
- C.5.5 Audio 2 Service ID 133
- C.5.6 Video Setup 134
- C.5.7 Video 625 Setup Menu 134
- Menu title: SET:VIDEO 135
- C.5.8 Video 525 Setup Menu 137
- C.5.9 Default Output Menu 138
- C.5.10 Audio Setup Menu 138
- C.5.12 Input Menu 141
- C.5.13 Outputs Setup Menu 142
- C.5.14 Alarms Menu 143
- C.5.15 Select Alarms Menu 143
- C.5.16 CVBS Output Menu 144
- C.5.17 GPOs Menu 145
- C.5.18 GPO X Menu 145
- Menu title: SET:REMOTE 147
- C.5.21 LS Data Menu 148
- C.5.22 Data Port Menu 149
- C.5.23 LS Output Menu 150
- C.5.24 ASI Output Menu 150
- C.5.25 ASI/SDI Outputs Menu 151
- C.5.28 IP Output Menu 152
- C.5.31 IP Output Menu 153
- C.5.32 IP Port Setup Menus 154
- C.5.33 IP Config Menu 155
- C.5.35 IP Port Source Menu 156
- C.5.37 IP FEC Menu 158
- C.5.38 CA Menu 159
- C.5.39 BISS Menu 160
- C.5.40 TV / AUD2 BISS Menus 160
- C.5.41 BISS 1 Menu 161
- C.5.42 BISS E Menu 161
- C.5.43 BISS E Key Menu 161
- C.5.44 BISS E User ID Menus 161
- C.5.46 Clear Carriers Menu 162
- C.5.47 System Menu 162
- C.5.48 Control Menu 163
- C.6 Status Menu 164
- C.6.2 Alarm Status Menu 165
- C.6.3 GPO Status Menu 166
- C.6.4 Input Status Menu 166
- C.6.5 Signal Status Menu 167
- C.6.6 TV Service 168
- C.6.7 Video Status Menu 168
- C.6.10 Audio Status Menu 169
- C.6.13 VBI Status Menu 171
- C.6.14 TV Data Status Menu 172
- C.6.15 PID Info Menu 173
- C.6.18 Downld Info Menu 174
- C.6.19 CA Module Menu 175
- C.6.20 CA Info Menu 176
- C.7 Properties Menu 178
- C.7.2 HW Config Menu 179
- C.7.3 Network Menu 179
- C.7.4 IP Address 179
- C.7.5 SubNet Mask 179
- C.7.6 Gateway Address 179
- C.7.7 MAC Address 180
- C.7.8 Customisation Menu 180
- Annex D 181
- Contents 181
- D.1 Alarm Conditions 183
- D.2 Input Stage Alarms 183
- D.3 Output Stage Alarms 184
- D.3.2 Audio Output Alarms 185
- D.3.3 VBI Output Alarms 186
- D.3.4 Data Output Alarms 187
- D.4.1 CA Related Alarms 188
- D.4.2 PSI/SI Related Alarms 188
- D.5 Config Alarms 189
- D.6 OAC Alarms 190
- D.7 IP Out Alarms 190
- Category 191
- Annex E 193
- E.1.1 Getting Started 195
- E.2.1 Scope of This Section 196
- E.2.3 Store Carrier Data 196
- E.2.4 Set Power up Carrier 196
- E.2.5 Force Carrier Retune 196
- E.2.8 Set Relays 197
- E.2.9 Local Lockout 197
- E.2.10 Abort NCP Command 197
Manuais e produtos relacionados com Recetor Ericsson TT1222
Recetor Ericsson RX8200 Manual do Utilizador
(8 páginas)
(8 páginas)
Recetor Ericsson LBI-38505A Manual do Utilizador
(197 páginas)
(197 páginas)
Recetor Ericsson TT1222 Guia do Utilizador
(20 páginas)
(20 páginas)
Recetor Ericsson RX8315 Guia do Utilizador
(40 páginas)
(40 páginas)
Recetor Ericsson RX8200 Guia do Utilizador
(44 páginas)
(44 páginas)
Recetor Ericsson RX8315 Guia do Utilizador
(24 páginas)
(24 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais